Polyglutamic acid keeps getting introduced as "the new hyaluronic acid", which undersells it and misreads it. Both hold water. Both are fermented. Beyond that they diverge quickly: HA is a glycosaminoglycan your skin already makes, PGA is a gamma-linked polypeptide from Bacillus fermentation that your skin has never seen, and the molecular difference shows up in the texture, the film and the claim you can measure.
Most polypeptides are alpha-linked, amino to amino acid in a chain the body's enzymes can cut. Polyglutamic acid is gamma-linked: the chain runs through the side-chain carboxyls, forming a loose, hydrated coil that proteases handle badly. That is why the material survives on skin long enough to matter, and why a PGA serum still feels present at hour eight.
The same structure makes it a strong film former. Where HA pulls water and mostly stays put, PGA lays down a smooth, flexible layer that slows transepidermal water loss measurably at low use levels. It is closer to a second skin than to a sponge, and products should be positioned accordingly.
Effective levels sit between 0.05% and 0.5%. Above roughly 1% you are buying viscosity, not function, and the stringiness that shows up will fight your pump and your panel's patience. This is worth knowing before you brief a supplier, because the price per kilo looks high until you price per finished unit and find it is one of the cheaper claim drivers on the sheet.
Viscosity is where the grade choice bites. High molecular weight grades, in the million-dalton range, give cushion and film but thicken fast and can go ropey at higher levels. Lower molecular weight fractions flow better and penetrate somewhat better, at the cost of some of the film effect. A blend of the two is what most finished serums end up using, and the ratio is a formulator decision, not a supplier decision.
PGA wins on persistence. The film survives cleansing-adjacent routines, holds water against a dry environment, and pairs well with HA by covering the hydration gaps a purely humectant system leaves after a few hours. It also carries fragrance and colourants more evenly in a serum base, for whatever that is worth to your development team.
It does not replace HA's slip and cushion at low dose, and a formula built on PGA alone tends to feel thin in the first application, which is the moment the consumer forms their opinion. Practical answer: HA in front for feel, PGA behind for duration, and a TEWL measurement at week four to prove the second half of that sentence.
Molecular weight or intrinsic viscosity stated per batch, not per product family. Assay by HPLC. Moisture content, since the material is hygroscopic and a wet drum lot dilutes your batch. Ash and residual media from the fermentation, with numbers rather than statements. Heavy metals and microbial limits, and a pH in the mildly acidic to neutral band.
Origin questions are worth asking too. Bacillus fermentation is the standard route, and a supplier who can name the strain and the purification steps is a supplier who controls their process. Insen Biotech supplies cosmetic-grade PGA with viscosity and purity per batch, on the product page, and trial quantities come with the batch documentation so your lab can feel the difference between grades before choosing one.
Add PGA in the cool-down phase where possible, because long high-temperature holds cost some viscosity. Watch your electrolytes: salt load flattens the film contribution faster than it changes the viscosity, so a serum heavy on minerals needs its PGA level verified against the finished system rather than the base. And if the product is an emulsion rather than a serum, check stability at 40 C for a month, because polyelectrolytes nudge emulsifiers in ways that only show after the fact.
Claims need care in the other direction. Water-binding multiples that come from lab comparisons at fixed humidity are not a licence to write them on a pack. The safe measurable story is the TEWL reduction, and that one holds up in an audit.
Yes, and most good barrier serums do exactly that. HA for immediate feel, PGA for duration. There is no chemical conflict between them.
That is the high molecular weight fraction announcing itself. Cut it, switch to a blended grade, or accept the texture and sell it as cushion.
No. It films better and flows worse. What the product needs decides, and that decision belongs to your panel, not the certificate.
If PGA is on your roadmap for next season, send us the product type and the claims you intend to carry, and we will suggest a grade and a starting level. Request a sample with batch documentation.